{"title":"Display","description":"","products":[{"product_id":"kukirin-display","title":"KuKirin Display","description":"\u003ch2\u003eKukirin Display\u003c\/h2\u003e\n\u003cp\u003eOn this listing we have 2 options available so please check before ordering.\u003cbr\u003eBoth displays are identical however one of the plugs is different due to changes that have been made to the lay out of controls on the handle bar over the production life of the scooters.\u003c\/p\u003e\n\u003cp\u003eOne of the displays has: 2x 2pin, 2x 5 pin and 1x 4pin connectors (2x red, 2 green, 1 blue)\u003cbr\u003eThe other display has :2x 2pin, 2x 5pin and 1x 6 pin connectors (2 red, 2 green, 1 black)\u003c\/p\u003e\n\u003cp\u003eBoth Kukirin displays essentially are the same but will not work if buying the incorrect one as all the connectors need to match.\u003c\/p\u003e\n\u003cp\u003eThe LCD shows indicators, odometer speed in KM or MPH, battery voltage, battery bar, Dual or single motor (if applicable)\u003c\/p\u003e\n\u003ch3\u003eKukirin display - whats in the box\u003c\/h3\u003e\n\u003cp\u003e1x kukirn G2 display\u003c\/p\u003e\n\u003cp\u003e1x mounting bracket (pair) already fitted so you can quickly and easily replace the entire unit.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch4\u003eKukirin display - Display Settings and error codes\u003c\/h4\u003e\n\u003cp\u003eKukirin display settings\u003c\/p\u003e\n\u003cp\u003eP01 : KM\/MPH\u003c\/p\u003e\n\u003cp\u003eP02: Voltage - this should be set at the level your scooter runs to (g2 pro and G2 max is 48v, G2 master is 52v, G3 Pro is 52v) this setting does not affect speed just the battery bar being accurate or not.\u003c\/p\u003e\n\u003cp\u003eP03: Wheel diameter in Inches\u003c\/p\u003e\n\u003cp\u003eP04: Speed measurement (30)\u003c\/p\u003e\n\u003cp\u003eP05: Cruise control (0 off\/ 1 on)\u003c\/p\u003e\n\u003cp\u003eP06 : Kick start (0 off\/ 1 on). On means you have to kick the scooter off for it to run, 0 means it will run from stationary without needing to kick off\u003c\/p\u003e\n\u003cp\u003eP08: Auto shut down timer in minutes of inactive use (1-5)\u003c\/p\u003e\n\u003cp\u003ePA : Torque - the power the motor puts down when accelerating\u003c\/p\u003e\n\u003cp\u003ePB : E-brake force (0 none, 5 full) we recommend 3 or 4 but its really personal choice.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003cp\u003eError codes and settings are the same across Kukirin the range\u003c\/p\u003e\n\u003cp\u003eE-001 : Rear motor malfunction - Motor sensors or communication problems, cable may be damaged or motor damaged.\u003c\/p\u003e\n\u003cp\u003eE-002 : throttle malfunction - Hall sensor or cable damaged, replace.\u003c\/p\u003e\n\u003cp\u003eE-003 : Controller malfunction - Check cabling - may need a new controller.\u003c\/p\u003e\n\u003cp\u003eE-005 : Battery under voltage - Battery may need charging or replacing if error persists\u003c\/p\u003e\n\u003cp\u003eE-006 : Instrument malfunction - Check all cabling. Diagnostics may have to be carried out to identify actual fault.\u003c\/p\u003e\n\u003cp\u003eE-007 : instrument malfunction - Check all cabling. Diagnostics may have to be carried out to identity actual fault.\u003c\/p\u003e\n\u003cp\u003eE-009 : Over-temperature protection - Controller is reporting high temperature (your probably overloading the scooter with to much weight or overly aggressive riding)\u003c\/p\u003e\n\u003cp\u003eE-011 : Front motor malfunction - (G2 master, G3 pro only) Motor sensors or communication problems, cable may be damaged or motor damaged.\u003c\/p\u003e\n\u003cp\u003eE-013 \u0026amp; E-017 : Controller malfunction - Diagnostics required, controller has developed faults.\u003c\/p\u003e\n\u003cp\u003eThe scooter.shop Ltd has a workshop and specialises in Kukirin products, so if you do face problems we can carry out repair work if necessary. We cannot solve problems over the phone unfortunately unless very obvious to yourself. If you do need work, just drop us a call or come down and book your scooter in for servicing.\u003c\/p\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch4\u003eKukirin display shipping\u003c\/h4\u003e\n\u003cp\u003eFree shipping is with Royal mail 48, this is a 2-3 working day service.\u003c\/p\u003e\n\u003cp\u003eIf you need your order fast then please opt for Royal mail 24 which is a 95% next day service.\u003c\/p\u003e","brand":"Kukirin","offers":[{"title":"4 Pin Blue","offer_id":51127623942475,"sku":"","price":49.9,"currency_code":"GBP","in_stock":true},{"title":"6 Pin Black","offer_id":51127623975243,"sku":"","price":49.9,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0900\/7638\/1515\/files\/display_Watermarked.jpg?v=1737317772"},{"product_id":"tf-100-lh-100-qs-s4-display","title":"TF-100, LH-100, QS-S4 Display","description":"\u003ch2\u003eTF-100, LH-100, QS-S4 Display\u003c\/h2\u003e\n\u003cp\u003eTF-100, LH-100, QS-S4 Displays, accelerator and settings controller with 6pin connection and USB interface.\u003c\/p\u003e\n\u003cp\u003eThese units are predominantly on 48v scooters such as the M4 pro. In the settings menu they can be changed to other voltages such as 24,36,48,52,60v \u003cbr\u003e\u003cbr\u003eThe display shows the various functions, Speed, battery, error code, odometer, Trip, gear.\u003c\/p\u003e\n\u003cp\u003eThe controller also features a USB charging output on the side (most people don't spot that) and we would advise its not used to charge phones or other gadgets as its simply an interface for programming.\u003c\/p\u003e\n\u003cp\u003eTo install simply remove the old display with an Alan key and unplug the cable. When installing the new display, make sure to test the angle of the accelerator lever before fully tightening the bolts. Plug back in to the din cable and away you go.\u003cbr\u003eThis install should not take longer than 5 minutes.\u003c\/p\u003e\n\u003ch3\u003eTF-100, LH-100, QS-S4 Display Error Codes:\u003c\/h3\u003e\n\u003cp\u003e0\/1 - No error\u003c\/p\u003e\n\u003cp\u003e2 - Brake - Check Brake sensor in the lever\u003c\/p\u003e\n\u003cp\u003e3 - Pas sensor error - check all cables are connected\u003c\/p\u003e\n\u003cp\u003e4 - 6KM\/H cruise\u003c\/p\u003e\n\u003cp\u003e5 - Timely cruise\u003c\/p\u003e\n\u003cp\u003e6 - battery under voltage - loose cables or BMS error, if the battery is reading the correct voltage then you may have to replace the motherboard\u003c\/p\u003e\n\u003cp\u003e7 - motor error - Check 5 pin connector in the scooter base - check cables are not damaged near the motor.\u003c\/p\u003e\n\u003cp\u003e8 - Throttle error  - check all cables are connected - Replacement Display may be needed.\u003c\/p\u003e\n\u003cp\u003e9 - Controller error - check all cables are connected - May need to replace motherboard.\u003c\/p\u003e\n\u003cp\u003e10 - Communication receive error - check all cables are connected - May need to replace motherboard.\u003c\/p\u003e\n\u003cp\u003e11 - Communication send error - check all cables are connected - May need to replace motherboard.\u003c\/p\u003e\n\u003cp\u003e12 - BMS communication error (battery circuit board) - check all cables are connected if the fault persists check the voltage of the battery.\u003c\/p\u003e\n\u003cp\u003e13 - Front light error. may need to replace is no obvious signs of loose cables\u003c\/p\u003e\n\u003ch4\u003eTF-100, LH-100, QS-S4 Display Settings:\u003c\/h4\u003e\n\u003cp\u003eIt is advisable that you do not change any of the settings on the Kugoo M4 Display, however understanding what the different programs mean you may be able to better diagnose problems with the scooter.\u003cbr\u003eP1 - Backlight\u003c\/p\u003e\n\u003cp\u003eP2 - metric\/ imperial  0 =KM, 1 =MPH\u003c\/p\u003e\n\u003cp\u003eP3 - Voltage 24\/36\/48\/60v (please note default is 36v, Do not change this setting unless you fancy upgrading all the wires and motherboard first, as a higher voltage will cause damage to fuses. This is a common reason for breakdowns)\u003c\/p\u003e\n\u003cp\u003eP4 - Sleep time 0 = none 1-60 minutes\u003c\/p\u003e\n\u003cp\u003eP5 - Gears 0 = 3 Gears mode (do not change)\u003c\/p\u003e\n\u003cp\u003eP6 - Rim size - Unit in inches adjustable to 0.1 of an inch (if changing tyre sizes)\u003c\/p\u003e\n\u003cp\u003eP7 - Speed testing magnetic steel number 0-255 (this relates to the magnets in the motor\u003c\/p\u003e\n\u003cp\u003eP8 - Speed limit 0-100kmh (do not use this setting)\u003c\/p\u003e\n\u003cp\u003eP9 - 0 push to start, 1 no push start required\u003c\/p\u003e\n\u003cp\u003eP10 - Drive set. 0 = pedal drive throttle will not work 1= throttle dictates speed, 2=both work but you will have to push to start (of no use so don't change)\u003c\/p\u003e\n\u003cp\u003eP11 - Pedal sensitivity (don't change)\u003c\/p\u003e\n\u003cp\u003eP12 - Pedal strength set (don't change)\u003c\/p\u003e\n\u003cp\u003eP13 - Pedal magnetic sensor set 5\/8\/12\u003c\/p\u003e\n\u003cp\u003eP14 - Controller current limit set 1-20Amp (default 13Amp)\u003c\/p\u003e\n\u003cp\u003eP15 - Controller under voltage settings\u003c\/p\u003e\n\u003cp\u003eP16 - Odometer, long press for 5 seconds to reset to zero\u003c\/p\u003e\n\u003cp\u003eP17 - 0: no cruise control, 1: cruise control\u003c\/p\u003e\n\u003cp\u003eP18 - Indicating speed ratio set, scope 50-150%\u003c\/p\u003e\n\u003cp\u003eP19 -0: with 0 gear, 1: no 0 gear\u003c\/p\u003e\n\u003cp\u003eP20 - 0= 2 number protocol. 1=5S protocol. 2\u0026amp;3= standby\u003c\/p\u003e\n\u003ch5\u003eOur Shipping options:\u003c\/h5\u003e\n\u003cp\u003eWith all our items we offer free UK post. Free post is using Royal mail 48 which is a 2-4 day service\u003c\/p\u003e\n\u003cp\u003eUpgrade to Royal Mail 24 for a small fee at checkout to receive your goods within 1-2 days Monday - Saturday.\u003c\/p\u003e\n\u003cp\u003eThe Kugoo M4 display will require a signature upon delivery. If they attempt to deliver and you are not in, using the card through the door you can have your item redelivered or dropped off at the nearest post office by using the app, See\u003cbr\u003e\u003ca href=\"https:\/\/www.royalmail.com\/services-near-you#\/\"\u003eRoyal mail \u003c\/a\u003efor more details\u003c\/p\u003e","brand":"My Store","offers":[{"title":"TF-100 \/ 5pin connector","offer_id":51142825050443,"sku":"","price":24.99,"currency_code":"GBP","in_stock":false},{"title":"TF-100 \/ 6pin connector","offer_id":51142825083211,"sku":"","price":24.99,"currency_code":"GBP","in_stock":true},{"title":"QS-S4 \/ 5pin connector","offer_id":51142825115979,"sku":"","price":24.99,"currency_code":"GBP","in_stock":false},{"title":"QS-S4 \/ 6pin connector","offer_id":51142825148747,"sku":"","price":24.99,"currency_code":"GBP","in_stock":true},{"title":"LH-100 \/ 5pin connector","offer_id":51142825181515,"sku":"","price":24.99,"currency_code":"GBP","in_stock":false},{"title":"LH-100 \/ 6pin connector","offer_id":51142825214283,"sku":"","price":24.99,"currency_code":"GBP","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0900\/7638\/1515\/files\/Hcbdf8c412d6949b4a19cc250a665d62eR.jpg?v=1737594315"}],"url":"https:\/\/thescooter.shop\/collections\/display.oembed","provider":"My Store","version":"1.0","type":"link"}